15 Reasons Why You Shouldn't Ignore Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs

Have your uPVC window or door mechanism become faulty? Maybe the window or door handles aren't aligned properly or are difficult to use.

You will lose energy if your double-glazed doors don't work properly. This increases the likelihood of burglaries. Owen the Locksmith can fix your door lock for a reasonable price.

Snapped Key

It can be a hassle when a key snaps into the lock. It also poses a security risk since the door might not lock and make you open to intrusion. There are a couple of quick fixes you can make to repair the issue and get your door working again.

First, remember to stay calm. If you panic and begin doing a lot of fumbling around, you might just end up pushing the damaged piece of the key further into the lock, which could make the situation worse.

Spray WD-40 or another penetrating oil, into the lock. This will allow the broken piece emerge more easily. You can also use a screwdriver to break off any pieces stuck. If you're fortunate enough to have a bit of the key left hanging out, you can make use of a paperclip or other thin metal object to grab it and then pull it out. Both methods are effective, but you need to be careful not to push the damaged key piece further into the keyway.

Some paperclips have grooved edges that can be used to extract hooks, and some Jigsaw blades can also be used for this function. If you don't have any of these available, you can use needle-nose pliers to bend and create hooks. You can also use a pair tweezers to grab and pull out the last bit of the broken keys.

If you're unable to pull the broken piece of key out, try using a lock de-icer. It's usually available at most hardware stores. It works by freezing any water or ice that could be in the lock.

If none of these strategies seem to be helping, it might be time to call in a locksmith. Fitlocks experts can solve problems like broken handles and snapped keys with uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms to ensure that they are easier to use. Request a repair for your double glazing through us online, or give us a phone call to discuss your needs.

Broken Cylinder

A broken cylinder is an extremely risky security issue. Luckily, it's an easy repair for an expert locksmith to complete. Locksmiths will need to tap the cylinder to fix it. They can do this with an hammer or another tool, but the best method is to make use of an extended match or piece of wire. Position the match or the wire's end in the keyway. The locksmith will strike the lock to crack it open. This is far better than using a heavy hammer that can damage the lock.

Overheating is the primary reason for cylinder heads to crack. This can occur when the cylinder head and block are made of various metals, such as cast-iron or aluminum. When different metals heat up and cool down at different rates, it could create hotspots locally that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion is a different reason for cylinder fractures. If the head and block of the cylinder are not maintained correctly, they can corrosion or rust, which can cause them to expand more than anticipated. As time passes, this may also lead to cracks.

If your uPVC window lock or door is stiff or requires lots of pressure to turn, it can be the result of a number of things. This issue could result from a defective locking mechanism or misalignment, as well as a worn-out handle.

Fortunately it's a simple and inexpensive fix for most homeowners with double glazing. A professional locksmith will usually fix this problem within one hour of arriving at the home. They can replace the locking mechanisms, or change the window handles and replace the gearboxes, depending on your particular requirements. A locksmith with experience can always advise you on the most cost-effective solution for your home. They can even suggest upgrades to high-security 3 Star Euro cylinders, TS007, that will add an extra layer of security against burglars. It's a small amount to pay for the peace-of-mind that comes from knowing your uPVC door is secured.

Broken Handle

It's not surprising that window handle locks can break. They have intricate mechanisms which deteriorate over time. If yours breaks it's difficult to determine the source of the issue and make sure you fix it properly.

The issue could be in the internal locking mechanism or the latch, fixing the broken handle will improve your uPVC double glazing door's security and allow you stop the draughts. It can be expensive to repair or replace your handle incorrectly and it could also harm the frame and the lock of your door.

Screwdriver Open the window and the screw loose, loosen the handle. This should be located on the inside face of the back plate, which is usually covered by an aesthetically pleasing cover for the screw reasons. Be careful not to damage any of the internal components inside the handle, such as the levers or plates on either side of the spindle. Keep them in the same order to make it easier to replace them if needed.

Next, turn the handle so it's at 90 degrees towards the window frame. Then, loosen the screw at the back of the handle that holds it to the internal spindle using another screwdriver. Once the screw is loose, remove the handle and take the broken spindle out. Replace this with a new one, making sure it is the same length as the previous one (you will typically find them on the internet or at hardware stores) and securely screw it into place. Be careful not to overtighten as this could damage the handle or the window frame.

Ensure the new handle is correctly installed, then close and test the handle. It should operate smoothly, and you will be able to open your window once again.

Don't forget to double-check that your uPVC window is shut correctly when you're using the handle. If they're not closing properly, you may experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. Core Sash Windows is a local window company that can adjust the hinges of the window frames to ensure that they shut correctly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is most common in uPVC tilt and turn windows. These windows require a handle that acts as a locking device in the window frame.  double glazing repairs Maidenhead  is attached to a central rod that triggers the cams with a mushroom shape that lock into the window frame keep. If the dead latch mechanism fails to open when the handle is turned it is possible that the spindle has broken and this could be a very frustrating issue.

There are ways to fix this issue. A professional locksmith can quickly and effectively fix this issue. A good locksmith will be able to disassemble the handle of the window by using a tool to remove the wheel part that houses the spindle. This can be done without damaging the handle or causing other damage to the window frame.

After removing the wheel the technician can inspect the spindle and determine what caused it to break. This involves breaking down the spindle into its constituent parts and carefully recording their general condition, as well as any specific areas of damage or excessive wear. This procedure is typically carried out by technicians working in a clean and safe environment.

The next step is to clean the damaged spindle, this will remove any dirt or debris that might be obstructing its normal operation. After this the spindle could be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is similar in size to the original. He will then drill holes that are identical to both pieces. This will ensure that the new spindle has precisely matched to the handle.

If the damaged spindle is beyond repair, it may be necessary to replace it completely. Home centers sell generic replacements, but if your window design is unusual you'll have to speak with a cabinet maker or woodworker who can make the exact part. Once the new spindle is installed, it can be fitted to the handle by line up the screw holes in the handle and the frame existing screws. Once the new handle is firmly seated you will be ready to operate your uPVC window.